MMD Equipment SDG150S-6A6 Installationshandbuch

1.Safety 1-7 Taking off the radiator cap  Be sure to stop the machine first and then loosen the radiator cap slowly, after the coolant water is s

2. Part Names 2-2 2.2 Internal Components SDG125S-6A6 1 2 3 4 5

2. Part Names 2-3 SDG150S-6A6 1 18 2 3 4 5 6

Preface ◆ This manual explains and illustrates proper handling of the unit, method of daily inspection and maintenance to enhance the performance of

3. Installation 3-83.3.3 The Maximum Combined Simultaneous Power Consumption  Never exceed the maximum combined simultaneous power consumption.

3. Installation 3-93.4 Selecting Cable  Select a cable with sufficient diameter by considering the permissible current on the cable and the distanc

4. Operation 4-14.1 Instrument panel SDG125S-6A6 1. Panel light switch 13. Diagnostic lamp 2. Frequency meter 14. Diagnostic b

4. Operation 4-2 SDG150S-6A6 1 2 3 4 5 6 7 23 22 21 20 19 18 17 8 9 10 11 12

Table of Contents 1. Safety ...

4. Operation 4-34.2 Protection device  For prevention of troubles during operation, this machine is provided with various protection devices. If

1.Safety 1-1This operation manual explains and illustrates general requirements for safety and cautions for safety. Please read these safety requi

5. Periodic Inspection/Maintenance 5-1 5.1 Important Items at Periodic Inspection and Maintenance or after Maintenance  The manual shows proper int

5. Periodic Inspection/Maintenance 5-25.2 Daily Inspection and Keeping Operation Log  Be sure to carry out daily inspection every morning before o

5. Periodic Inspection/Maintenance 5-35.3 Periodic Inspection List Such items marked ○ shall be carried out by customers. For the following items

5. Periodic Inspection/Maintenance 5-45.4 Periodic Replacement of Parts  Air filter is a crucial component for the performance and the life o

1.Safety 1-21.1 Caution before Operation Ventilation  Exhaust gas from the engine is poisonous, and could cause casualties when it is inhaled

5. Periodic Inspection/Maintenance 5-115.5.14 Change Coolant  1,000 hours or every 2 years Taking off radiator cap  Be sure to stop the machin

5. Periodic Inspection/Maintenance 5-12(Procedure) ① To drain coolant, remove the radiator cap“1”, then loosen the drain valve“2”. ② Be sure to also

5. Periodic Inspection/Maintenance 5-135.5.15 Change Air Filter Element  Every 1,000 hours  When an element that is clogged or has holes or

6. Maintenance/Adjustment 6-16.1 Maintenance of Battery Handling battery  Keep flames away from battery.  Battery may generate hydrogen gas and

6. Maintenance/Adjustment 6-36.2 Troubleshooting  Should any trouble occur during operation, do not leave it. Investigate the cause and take approp

6. Maintenance/Adjustment 6-4 Symptom Cause Counter measures Even when operated at a rated speed, no voltage or too low voltage generated. (1) F

7. Storage of the Unit 7-17.1 Preparation for Long-term Storage When the unit is to be kept unused in storage for a long time, be sure to follow

8. Specifications 8-18.1 Specifications Model SDG125S-6A6 Exciting system Brushless system Armature connection Star with Neutral ZigZag Phase

1.Safety 1-3 Safety outfit  When handling machine, do not wear;  loose clothes  clothes with unbuttoned sleeves  hanging tie or scarf  dangli

8. Specifications 8-2 Model SDG150S-6A6 Exciting system Brushless system Armature connection Star with Neutral ZigZag Phase number Three S

9. Wiring Diagram 9-2 SDG150S-6A6 Terminal plate A050586A.C.Generator To BatteryTo Monitor lamp

39600 58921PRINTED IN JAPAN 2005.11ＨＯＫＵＥＴＳＵ ＩＮＤＵＳＴＲＩＥＳ ＣＯ., ＬＴＤ. 12TH FLOOR SHINJUKU SAN-EI BLDG, 22-2 NISHI-SHINJUKU 1-CHOME,SHINJUKU-KU

1.Safety 1-41.2 Caution during Operation Never touch the output terminals and interior of control board  Never touch the output terminals du

1.Safety 1-5 Do not touch hot parts  Never work nearby hot portions of the machine while it is running.  Do not touch hot portions of the machin

1.Safety 1-61.3 Cautions during Inspection and Maintenance Hang a “Now Checking and under Maintenance” tag  Before starting inspection,